U.S. Patents 6.016,836 and 6,899,733

Shower Manager
The Shower Timer that Cuts the Flow


Installation Guide

Shower Safety First

What's in the box?


Contents of the box
  • 1 Shower Manager
    (Battery Installed)

  • 1 Instruction Sheet

  • 1 Rubber Washer
    (for Inlet)

  • 1 Programming Magnet


Missing something? Complete the parts request.


Recommended Installation

Typical Installation

The Shower Manager was designed to be installed between your existing showerhead and the supply pipe (shower neck).

By design, the Shower Manager is sensitive to pressure and flow changes, so it is not recommended for use in combination with other flow-controlling devices or accessories that can cause significant pressure changes. Things such as, but not limited to:
  • Pulsating or massaging shower heads
  • Shower heads equipped with on/off valve
  • Hand-held shower heads
  • Oxygen combining shower heads
  • Ultra-low flow shower heads with less than 1.8 GPM
  • In homes with very low water pressure (<40 PSI)
While these types of shower heads may work, they may also introduce problems when used in conjunction with the Shower Manager.

Important: Do not attach a showerhead on an extension arm of any size to the Shower Manager, this can damage the unit and void your warranty.


Tips for Successful Use


Get the family on board!
Let everyone involved know about what you hope to accomplish by using the Shower Manager and create a reward system for when the goals are reached.


Plan ahead!
During the 5 minute reset period only a reduced flow of water is available. Only after this time has elapsed, will the Shower Manager will restart in Full-Flow Mode.



Color Installation Instructions

Download Instructions

Setting the Shower Time

Note: The Shower Manager comes ready to use, pre-programmed with the 5 minute full-flow setting for maximum water and energy savings.

How to change the shower time. Beep Key
Locate the magnet below and place it on the Shower Manager as shown.
Notice: The line or rasied bar on the side for correct placement of the magnet. Slowly move the magnet from the front to the back along this line until you hear 1-3 beeps. The number of beeps indicates the current time setting.

Note: The unit can't be programmed while in full-flow, reduced-flow, or during the reset period. If the unit refuses to respond to programming, wait a full five minutes before trying again.

To change the time setting:
Repeat the placement of the magnet on the line, but hold it there until the number of beeps changes to correspond with your desired time setting.

Beep KeyBeep Key


1 beep = 5 minutes

2 beeps = 8 minutes

3 beeps = 11 minutes


Standard Model times shown



Prepare for use.

Prepare your shower timer Verify the included rubber washer is installed in the water inlet. Correctly installed, this washer provides a drip-free seal.

Prepare your threads Optional: In the event of drips due to damaged threads preventing a good seal with the washer. It is recommended to wrap the threads on the shower neck with 2-3 wraps of Teflon thread seal tape (PTFE plumber's tape - not provided).

Notice - No dope allowed IMPORTANT: Use of anything other than Teflon tape can damage the Shower Manager & void the warranty.

Installing the Shower Manager

showertimer-install Step 1 1 Remove showerhead.
Carefully thread on the Shower Manager and tighten just enough to prevent leaking. 2 Carefully thread the Shower Manager onto the supply pipe until snug, then hand-tighten just enough to stop water leaks.
Replace your showerhead. 3 Replace the shower head, being careful not over-tighten as this can damage the unit and void the warranty.

Having trouble? See the troubleshooting guide.
Have questions? See the FAQ.


 





We take Pay Pal Trust Authorize.net The American Made Shower Timer

Contact Us



Questions?
Call the help line: 303-695-5540
info@ShowerManager.com
Shower Manager LLC
2942 S. Trenton St.
Denver, CO 80231 USA

FB Icon Twitter Icon

U.S. Patents 6.016,836 and 6,899,733

© 2016 Shower Manager, LLC